Tuesday, November 8, 2011

Replacement gilts / marking pigs / breeding / handling

 We sorted through 800 piglets to find the 15 that will be our replacement gilts; and when I say sorted, I mean we got down and counted nipples and inspected every inch of those 800 piglets.

 This little group of pigs has been getting very special treatment.   A gilt is a virgin pig; when she has a litter, she is then considered a sow.  We actually sorted out and selected 17, but 2 of those didn't make the cut this time, and so we're ear tagging 15 of them.  Andrea is carefully leaning over to tag the left ear.    We tag the left ear as a standard.  If the tag falls out there's a hole in the left ear, and we check that before we take pigs to market as a fail-safe.  We raise the breeders with the other pigs and separate at market time. 
 We tag the pigs so that we can track their progress, health and litter characteristics.  If you're going to be breeding, you want to be able to identify each animal, and since we've got 5 people who work with these pigs, we need to be able to say "hey, #57 looks like she's about due; can you look at her?"

We use the hog panels you see in these pictures pretty much everywhere.  They're the duct tape of hog operations.  In this case the pen itself is formed with hog panels, and then we've brought a spare one in to form a temporary pen inside the larger pen, so that we don't have to chase the pigs around while we're tagging them. 

When you have 200 to 400 pigs around at any given time, it's hard to remember the details of each ones history.  Records are important. 
Marking pigs can take many forms; ear notching is pretty common.  In the bigger hog farms, tattoos are used.   We don't tag the majority of the animals; just the breeders, and we don't retain very many.  15 out of 800 is about 1.8%, which is in keeping the the philosophy that you only breed the very best. 

It's pretty common on pig farms, especially on those that are raising heritage breeds, to believe that anything that comes out of a sow is breeding material.   If you're going to be serious about saving a breed, I think you should be serious about improving it, too.  And you do that by learning to evaluate a pig at various ages, and by tracking your results. 

Your desired results can vary.  For me, I want calm, good mothers who work well on pasture and wean a large percentage of their litters.  A couple of these pigs were chosen because they were particularly friendly; temperament is important to me, too. 

These guys are F1 yorkshire/hampshire cross piglets.  that means that two purebred animals were used to produce them.  I've found that they make good mothers, and I'll be crossing them with a purebred berkshire boar to produce my market piglets. 


Sunday, November 6, 2011

Building a hoophouse from scratch: Initial design


I've been looking at temporary buildings to house my pigs during the rainy season, and a hoophouse seems to be the best candidate. 

For my purposes, a building that can be used for multiple purposes is ideal.  In the fall and winter, housing livestock.  In the spring and summer, growing things.  As a bonus, the deep-litter system that I'm going to try will produce (in theory) good compost, which, helpfully, will be placed right where it's going to be used -- in the greenhouse.  Sounds good, right? 

I'm going to go a little more expensive in my design by having the greenhouse itself rest on ecology blocks.  I'm going to do that so that I use my tractor to move materials into and out of the greenhouse.  The easier I can make the maintenance the better it is -- and the more likely that it will get done.

So the project breaks down into three parts: 

1) Initial design.   How big will it be, what materials will I use, and what will it cost?  How much of each material will I need, and where do I get them from?  

2)  Fabrication.   Taking the pipes that form the framework, how do I bend and form them so that they form the hoops that I need.   Addition of additional pipes and bracing to make the structure stronger.   Placement of the ecology blocks and anchoring the structure to them.  Covering the whole thing in plastic.  Securing the plastic. 

3)  Pig prep:  Additions to the building that make it likely to survive curious pigs and amenities to make it easier on the farmer -- food and water handling, access doors, and so on. 

Initial design
On my farm I have never said "gosh, this building is too large".  Ever.  With that said, the cost of building a bigger building, or the biggest you can afford, is often well worth it.  If nothing else you'll have extra space -- and that's often pretty handy for things you didn't know about.  Extra space in your greenhouse means you can store your soils and amendments there, for instance.

Choosing a hoop size
With hoophouses the limiting factor is the size of the plastic cover available, and basic math.  Here's an example of a supplier of greenhouse plastic in my area, and from that I can see that I can get plastic sheets in sizes up to 100'x48', and no bigger.  Here's a table of greenhouse sizes and the maximum hoop size for each one: 

Plastic cover width/Max hoop size
48'/30'
40'/25'
36'/23'
32'/20'
20'/13'
16'/10'

Other covering choices considered:
You can get larger covers; they're called hay tarps, and you can order them in any size.  there are also fabric barns that get their fabric from somewhere; I chose to do a transparent plastic covering because I want to use it as a greenhouse, too.  If I were doing a permanent pig barn, I'd seriously consider figuring out who makes the coverings for fabric barn resellers and getting a light colored fabric cover made. 

I'm assuming that the plastic covers the entire arch, from end to end, as well.  You could shorten it a bit with a pony wall. 

The shape of the hoop is strongest if it's a smooth, even arch all the way across.  These calculations assume that the shape of the hoop is half of a perfect circle.    Here's how I calculated it: 

Width of desired hoop / 2 * 3.1415 

Note:  You might need ladders or scaffolding
This also means that if I have a 30' wide barn, the top of the hoop in the center will be 15' tall.  Assembly will require some way to get up there to do the work of putting it together.  More on that later.  With a traditional use as a greenhouse it would be very difficult to use that extra height.  If I were designing to only grow plants and had smaller equipment, I'd consider a shorter greenhouse.

Will it work with the tractor?
With a circle, as you get closer to the edge you'll loose ceiling height, which for me is important to note.  I want to get pretty close to the edge of the building with my tractor.  The ceiling will be 10' tall 5' in from the base of the hoop.  which means that if I put the hoops on 2' ecology blocks, I should be able to get within 2 feet of the wall, which is close enough for me. 

(How did I figure that out?  The old fashioned way.  I drew a circle on graph paper using a pencil and a piece of string.   Each square on the graph paper represented 5', and after I drew it I could look to see where the pencil line and graph paper line intersected.  You can print graph paper online. )

How much material do I need? 
I cheated a little.  The picture at the top of this entry is a commercial greenhouse that I bought used, so I've got it as a reference point for building this one;  it helps that I've already put one of these together and pretty much know what's involved, and that the design has proven durable enough for my climate. 

I'm going to use a 4' hoop spacing, and I'm going to NOT use the truss system that the other greenhouse used.  I'm going to try using a heavier, larger pipe to eliminate the need for trusses for tractor clearance purposes.

So here's the math: 

Length of complete hoop house / hoop spacing = number of hoops
Width of each hoop / 2 * 3.1415 = length of each hoop
length of each hoop / pipe length = number of feet of pipe you'll need.

For this project:  80' long / 4' spacing = 20 hoops
30' wide hoops / 2 * 3.1415 = 47.1 feet per hoop (round up)
48 / 10' pipe length = 5 sticks of pipe per hoop (round up)

100 10' long pipes will form the hoops

You'll also want purlins -- pipes that run the length of the structure, usually one on either side, and one along the top.   The design I'm looking at (see picture at top) has 5 of them.  Two on each side, one along the top.  I'm going to copy that directly. 

80' x 5 = 400' of purlin, or 40 10' lengths.
Purlins can be smaller than the hoop pipe.  I'm going to be using 1.5" or larger pipes for the hoops, but the purlins will be smaller: 1 3/8" pipe, or 1" pipe.  The purpose of the purlin is the keep the hoops in position to stiffen the structure. 

One thing that the greenhouse design doesn't have is diagonal bracing at either end.  I'm going to add diagonal braces to strengthen the ends of this structure, one on each corner.  I want the braces to be attached to 4 hoops, so I'm going to make them about 20' long, each. 

80' of purlin-sized pipe for diagonal bracing. 

Prices and sources; next entry. 




Saturday, November 5, 2011

The new tractor!

 Just bought a (new to me) tractor, a Kubota M125x.  It's a 2008, and has 300 hours showing; to me that's a brand-new tractor.  As part of the proof the paint hasn't been worn off the front loader... 

It's pretty close in size to the Kubota 9580 we've been using as our farm tractor, but the 9580 is in the shop getting a new clutch installed, and I ran across this one local.  After a bit of haggling we settled on a price that neither of us were thrilled about (I thought it was too much, they thought it was to little) and sealed the deal by adding 3 finished pigs to it.  So for some cash and 3 pigs, the tractor is mine.   It's pretty hard to price tractors.  Even the same year and model will have asking prices that vary by 25%. 

 The front loader is rated to lift 4,000lbs, and there's a forklift that quick-attaches on to the loader so that you can handle pallets easily -- which I'm looking forward to.  The bucket in these pictures is 8' wide and 30" high, which doesn't seem like much...
until you get the scale of it by looking at the picture above.  That's Dan standing in the bucket, loading some 33 gallon garbage cans of chips.  A heaping load in the front loader seems to be about a cubic yard, or maybe a yard and a half, which means moving the chips around just got a lot faster. 

For areas where we want to rebed, but cannot get the tractor in, we'll fill garbage cans with chips as chore buckets, and then move the chips in the can to where they're needed.  In this case the chicken coop needed some new chips.  Toss the cans into the bucket, drive the tractor to the chip pile, fill the cans, load them on the front loader and return to the chicken coop. 

The rear tires are filled with calcium, and that provides extra weight to counterbalance the front loader.  So far I'm pretty happy with the tractor.

Unfortunately for me, a million small birds decided to roost on it last night, and I'm going to have to pressure wash it off.  I really need a garage.